Santi Heated Flex Undersuit and Glove Duo

The Santi Heated Flex Undersuit and Glove Duo includes the Flex 2.0 Undersuit with bag, Heated Gloves with all necessary cables and a Drysuit Connector or Thermovalve.

Santi Heated Flex 2.0 Undersuit

The Santi Heated Flex 2.0 Undersuit is light and flexible. The Climashield Contour fabric allows for full flexibility in every direction, leading to unique mobility and less bulk when compared with BZ400 Heated Undersuit.

The Heated Flex 2.0 contains very efficient heating wires that provide optimal thermal comfort during long and cold dives. Most of the generated heat is passed on directly to the diver’s body in this configuration.

Thanks to new, non-quilted fabric quality, the Flex 2.0 provides more warmth towards the body. This generates better thermal properties and keeps the heat trapped closer to the body for longer.

It is advised to wear the Santi Heated Flex 2.0 Undersuit on top of thin thermal underwear. This configuration directs the temperature straight to a diver’s body. The Heated Undersuits should not be worn directly on skin due to safety and hygienic reasons.

• Operating time on 24Ah battery: approx. 2h 30min - 3h
• Built-in heating glove wires
• Handy pocket on the waist for a power cord
• P-valve hose opening
• Net cuffs with rubber loops for thumbs
• Elastic gussets under the armpits
• Two side pockets
• Elastic waistband
• Two-way entry zipper
• Foot straps
• Maximum heating temperature: 45ºC
• Maximum heating power: 110W
• Climashield Contour 180g/m2 thermal insulation
• Safety switch prevents overheating
• Wires covered with ultra-soft silicone resistant to breaking
• Power cable is resistant to high temperatures and cuts
• Ergonomic nesting and wire layout
• Men’s stock sizes. Made-to-measure option for ladies and men

FREE "Made to Fit"

Very few divers require a totally made to measure suit due to the wide range of standard sizes available from Santi Diving. With this in mind, Santi offers a free of charge Made-to-Fit service to any standard size Heated Flex 2.0 Undersuit ordered, sculpting standard suits to a divers' measurements.

With your order, you can request up to 4 changes (ranging from 2 to 5 cm) to any of the standard size measurements listed under chest, inner arm, biceps, forearm, waist, hips, inner leg, thigh, calf or body trunk on the Santi size chart.

If you would require more than 4 changes to make your suit perfect, you can add two more changes for a small additional charge.

Santi Heated Gloves 2.0

Santi Heated Gloves 2.0 are very soft and do not hinder movements. The thin heating cables are arranged and sewn to be practically imperceptible. Under your dry glove you don’t feel the difference – is it your normal gloves or the heated ones? But you can feel the difference in the comfort you experience.

Hands are the first to get cold. When chilled and numb, they cause discomfort. But they are also incapable of properly handling inflators or valves, taking pictures or videoing. Capable hands are also helpful if you want to quickly escape troubles underwater.

Evenly distributed heating wiring that allows for freedom of movement in palms. The gloves keep your hands warm even when the heating is not on.

Heated Gloves can be easily connected to Santi Heated Vest or Undersuits without additional cables.

• Includes: gloves and cables
• Breathable fabric
• Maximum heating temperature 45°C
• Maximum heating power: 36W (pair)
• Maximum operating voltage: 12V

Thermovalve or Drysuit Connector?

Both the Santi Thermovalve 303 and the Drysuit Connector are used to connect an external power source to your Santi heated vest, heated gloves or heated undersuit. Both are available in Apeks or SiTech fittings.

The SANTI Drysuit Connector does this by being attached to your existing drysuit inflation valve, continuing to use the original valve for inflation and running power through the connector element. It adds 19mm height to your valve.

Thermovalve 303’s great advantage is placing the cable with the E/O connector in the down position, with the possibility of turning the head by 270 degrees, which allows for trouble-free connection of the hopper cable both in the position of the connector to the right and left.

Read our SANTI Thermovalve and Drysuit Connector comparison

Santi Heating Systems at glance

FREE "Made to Fit"

Very few divers require a totally made to measure suit due to the wide range of standard sizes available from Santi Diving. With this in mind, Santi offers a free of charge Made-to-Fit service to any standard size suit ordered, sculpting standard suits to a divers' measurements.

With your order, you can request up to 4 changes (ranging from 2 to 5 cm) to any of the standard size measurements listed under chest, inner arm, biceps, forearm, waist, hips, inner leg, thigh, calf or body trunk on the SANTI size chart.

Heated Gloves

UNDERWATER EXPLORERS LTD/DIRDIRECT DISCLAIMER:
It is the customers responsibility to choose a correct drysuit size. Modified undersuit returns are not accepted under any circumstance unless Underwater Explorers Ltd/DirDirect has made a mistake. We do not take any responsibility for a fit of suits unless measured by us. 

HOW TO MEASURE YOURSELF FOR SANTI SUITS

Carefully watch SANTI's Instructions for Measuring video below. The video shows all measurements for made to measure suits. For standard size or Made-to-Fit measurements please use the Size Chart.

STEP-BY-STEP

Never take your own measurements yourself! Measurements should be taken by another person to make sure all measurements are taken tight up to the body and at correct placement for a specific measurement.

It is important that you stand straight, look forward and do not bend over while you are being measured. It is equally important to take the measurements only while wearing thin clothing, close to the body. Don’t leave any additional measurement allowance.

CHEST - on the widest point.
INNER ARM - from armpit to wrist.
BICEPS - widest point on the loose arm. If you have a visibly athletic figure it is advised to measure the biceps also with bent elbow.
FOREARM - in the widest point.
WAIST - measure on the belly button level. Remember to measure the waist line in the widest point on the belly button line. To measure a female waistline correctly, use any kind of "marker belt" and fasten it around the waist line.
HIPS - in the fullest point of the buttocks.
INNER LEG - hold one end of the measurement tape in the crotch and measure to the heel end.
THIGH - widest point approximately 5cm from the crotch area.
CALF - measure the calf at the widest point.
BODY TRUNK - hold one end of the tape on the central point of the neck end and lead the tape across the crotch to the back. Mark the place where tape ends and measure the rest of the line to the spine neck bone. Make sure the tape is close to the body including all the curves.

UNDERWATER EXPLORERS LTD/DIRDIRECT DISCLAIMER:
It is the customers responsibility to choose a correct drysuit size. Modified undersuit returns are not accepted under any circumstance unless Underwater Explorers Ltd/DirDirect has made a mistake. We do not take any responsibility for a fit of suits unless measured by us. 

SHIPPING:

We aim to dispatch all in-stock items within 2 working days but will inform you of approximate delivery times should any item on your order be out of stock or on supplier backorder due to current manufacturing or transport delays caused by global shortages and/or impeded production.

Please refer to our Shipping Policy and Returns & Refunds Policy for detailed information on delivery terms and returns.

Our current shipping rates are as follows:

• UK mainland orders £45 and over: FREE
• UK mainland orders under £45: £4.90 Fixed Rate
• Channel Islands, Isle of Man & Highlands: £9.90 Fixed Rate
• Northern Ireland: £14.9 Fixed Rate
• European Union: £13.90 + 5% of order value (maximum £30)
• Rest of the World: £19.50 + 8% of order value (maximum £55)
• BFPO Post Codes: £20

INTERNATIONAL EXCEPTIONS:

For international orders containing weights, cylinders (excluding suit inflation bottles) and Suex scooters please contact us in advance before placing your order.

These products are not included in our global max-capped shipping rates and are only shipped outside of UK mainland after freight cost is calculated based on total weight, dimensions of parcel, location of delivery and the courier service used. We will let you know what this cost will be before processing any order.

All cylinders we ship within and outside of UK mainland are filled and tested on site before being emptied for dispatch. Cylinders shipped outside of the UK will be empty and will also have their valves removed, requiring reassembly after you receive delivery. Twinset manifolds and bands will also be removed and dispatched together with the cylinders for safe global shipping.

RETURNS & REFUNDS

We offer a 30 day return for any product sold under our Returns & Refunds Policy Please contact us before any return with your order number and date details. Receive our Returns Authorisation Form and instructions and enclose them with your return to expedite a refund. Detailed information is available in our Returns & Refunds Policy.

Email us at sales@dirdirect.com or call us on +44(0)1305 824 555

Note that all returned items are shipped at the customer's own risk and remain the customer's property until received by Underwater Explorers, so please ensure they are packaged well and use reliable postal services with tracking facilities. The goods will be inspected on arrival. 

Return postages are at your own cost and our outbound shipping costs (if items are sold with integrated basic shipping charges i.e. Free shipping for orders £45 and above) the UK shipping rate may be deducted from any UK mainland refund unless linked to a fault/defect claim. 

Please contact us with your order number and name before sending any returns to:

Underwater Explorers – Returns
Unit 1, Maritime Business Centre
Mereside, Portland
Dorset, DT5 1FD 
United Kingdom

Please refer to our Shipping Policy and Returns & Refunds Policy for detailed information.